Wheel center cap 60 MM design Car

How to select correct type of 60 mm wheel center cap with Car logo

1. Measure A, B, C on your existing cap according to this drawing:

*** if you do nor have any caps, you need to measure your wheel. Manual is HERE.

               Click to enlarge

2. Prepare your measured values ​​of A, B, C and compare with right part of the table

- start with comparing dimension C, that will narrow your options to one or few variants
- then continue with dimension B, that will again narrow to one or maybe to caps variants
- and as last compare dimension A.

At this point you should have only one cap in your scope. If there might still be two options
compare also dimensions  D, E and F and select one with dimensions that fit  the best.

3. Write down selected center caps type add it to your order

If you need advice, send us email with the dimensions you have measured.

Overview of wheel center cap types with diameter 60 mm									COMPARE YOUR MEASUREMENTS WITH BELOW RANGES In order to have the center cap fit your wheels, dimensions A, B and C measured by you   MUST BE within all three  A, B and C tollerances.
SPECIFICATION
Cap type to order	Photo click to enlarge	A	B	C	D	E	F		A	B	C
1010		59,7	55,5	2,0	3,6	8,0	3,0		59,5 - 60,2 mm	55,3 - 55,7 mm	2,0 - 2,4 mm
1013		60,1	55,3	2,2	4,0	7,0	3,5		59,8 - 60,5 mm	55,1 - 55,5 mm	2,2 - 2,6 mm
1015		60,1	56,0	2,3	4,0	8,0	3,5		59,8 - 60,5 mm	55,8 - 56,2 mm	2,3 - 2,7 mm
1028		59,0	54,0	2,5	4,0	5,7	7,0		58,8 - 59,5 mm	53,8 - 54,2 mm	2,5 - 2,9 mm
1035		59,0	54,0	3,0	5,0	7,5	5,5		58,8 - 59,5 mm	53,8 - 54,2 mm	3,0 - 3,4 mm
1016		59,0	56,8	3,0	5,0	9,5	3,6		58,8 - 59,5 mm	56,6 - 57,0 mm	3,0 - 3,4 mm
1036		59,3	56,0	3,0	5,0	8,0	3,5		59,1 - 59,8 mm	55,8 - 56,2 mm	3,0 - 3,4 mm
1033		59,8	55,0	3,5	6,0	9,0	3,5		59,6 - 60,3 mm	54,8 - 55,2 mm	3,5 - 3,9 mm
1011		59,0	54,9	4,0	6,0	9,0	3,5		58,8 - 59,5 mm	54,7 - 55,1 mm	4,0 - 4,4 mm
1024		59,0	55,1	4,0	6,0	9,5	2,6		58,8 - 59,5 mm	54,9 - 55,3 mm	4,0 - 4,4 mm
1038		59,0	55,5	4,5	6,5	9,2	2,5		58,8 - 59,5 mm	55,3 - 55,7 mm	4,5 - 4,9 mm
1040		58,5	53,0	5,0	7,0	11,0	4,0		58,3 - 59 mm	52,8 - 53,2 mm	5,0 - 5,4 mm
1021		59,5	54,3	5,0	7,0	9,0	2,0		59,3 - 60,1 mm	54,1 - 54,5 mm	5,0 - 5,4 mm
1023		59,5	55,7	5,0	6,5	9,1	3,0		59,3 - 60,1 mm	55,5 - 55,9 mm	5,0 - 5,4 mm
1006		59,0	56,0	5,3	7,0	10,0	2,5		58,8 - 59,5 mm	55,8 - 56,2 mm	5,3 - 5,7 mm
1005		59,0	56,0	5,5	7,8	11,5	2,8		58,8 - 59,5 mm	55,8 - 56,2 mm	5,5 - 5,9 mm
1039		59,0	Typ SHAPER				2,7